Twisted Tuck Wristlet tutorial by mahlicadesigns

Feature collage

For the September Sew With Me challenge on facebook, I needed to make an accessory. After being stumped a while, I came up with an idea for an accessory that I actually needed; a small purse with a handle. I drafted my own pattern, so I wanted to do a practice run before working with a faux leather for my final version. The first version out of quilting cottons was made up for my So Sew Easy Sewing Swap partner. I hope she likes it.

Since I put in some effort to draft my pattern and work out the twisted tucks detail, I wanted to share a tutorial so you can make one too.

You’ll need:

Twisted Tuck Wristlet template, 4.5in X 14in rectangle for twisted tuck detail, 3in X 11in piece for strap, 11in X 8in for interior pocket (optional), fusible fleece or heavy weight fusible stabilizer, 9in zipper.

Cut Exterior Fabric: 1 main body, 2 front side pieces, 1 tuck piece, 1 strap piece

Cut Interior Fabric: 2 main body, 1 pocket.

Cut fusible fleece: 2 main body (hint: trim away about 1/2in from edges to reduce bulk in your seams, especially at the top edge)

First we’ll make the twisted tucks insert.

  1. Grab your 4.5 x 14 inch piece. Mark one of the shorter ends on the wrong side as the Top. Make your first fold, wrong sides together, 2in down from the Top edge. Press. Sew 3/4in away from and parallel to your folded edge.**
  2. Make your next fold, wrong sides together,  1 5/8in down from the stitching line you made in step #1. Press and sew 3/4in from your folded edge. Repeat until you have a total of five tucks.
  3. Press tucks down. Baste tucks down on one edge using 3/8in seam allowance. Fold and pin tucks up on other side. The edges will not line up squarely, that’s ok, its more important to keep the piece squared up. Baste in place using a 3/8in seam allowance. You should have 1/2in of fabric above your top tuck and more below your bottom tuck.Tucks collage
  4. Using a 1/2in seam allowance, attach the side pieces to the tucks insert, lining the pieces up at the top. Press. The insert should be a little longer than the side pieces, trim away any excess after the side pieces are attached.

front

Next, we finish getting our pieces ready.

5. Trim 1/2in away from the top, flat edge of the fleece if you haven’t done that already. Apply the fusible fleece to the wrong sides of the two exterior pieces.

6. Press the pocket piece in half lengthwise, wrong sides together. Center the pocket on top of one of the lining pieces, right sides up. The lower raw edge of the pocket should line up with the lower edge of the lining piece. Bits of the pocket will hang over. To make a 3in card slot, I mark the center of the pocket, then measure and mark 1.5in out each side of center. Stitch along the marked lines, backstitching at the top to reinforce. You can divide the remaining pocket area as desired or leave them alone.  Tip:  1.75in to 2in width is good for a lipstick slot. Trim off any overhanging parts of the pocket.Pocket7. Press the strap in half lengthwise wrong sides facing. Open up, fold long edges in to meet at the center, press, and fold again. Same as if you’re making a double fold binding. Stitch 1/8in from the folded edges to close the strap. Place one of the exterior pieces right side up. Position the strap 1in down from top edge and with raw edges facing out. Baste in place.

backAssembly:

8. Mark a line 1/8in down from top edge on right side of a Lining piece.** Position the zipper right side up along this line, making sure the top zipper stop is about 3/8in in from the side. Pin in place. Position one of the Exterior pieces on top, right side down. The zipper is sandwiched between the layers. Using a zipper foot, stitch 1/2in from edge. Repeat with the second lining and exterior pieces.

Wristlet zipper insertion collage

9. Open out the layers so zipper is in the center. Press and topstich about 1/8in away from exposed zipper tape.

Top stitching collage

10. With needle & thread, make a new zipper stop about 3/8in from edge. Trim away excess length of the zipper. Open zipper by about 3/4s.zipper end collage

11. Fold one exterior piece over onto the other exterior piece, right sides together. Line up exterior and lining pieces, making sure open edges of zipper are lined up. Pin as needed.

12. Leave a 3in opening at the bottom edge of the lining pieces. About 1.5in from center bottom of lining, start stitching with a 5/8in seam allowance, as you sew around the curve gradually change your seam allowance to 1/2in. before you reach the zipper. Sew slowly as you go over the zipper. As you come back around to the lining, increase your seam allowance to 5/8in after the curve.stitching

13. Carefully trim excess bulk from the zipper corners. Clip the curves and trim seam allowance around the bottom edge of the lining by about half.

14. Pull the wristlet right side out through the opening in the lining. Hand stitch the lining closed. Use a turning tool to push out the corners at the top and smooth out the lining and curves.

lining opening

Zip it up and your done!

Final collage 3

** This sentence edited after publishing to be more clear.

16 thoughts on “Twisted Tuck Wristlet tutorial by mahlicadesigns

  1. I love the twisted effect! So pretty! Really easy to follow instructions too. I’ll definitely have to give this a go soon.

    Like

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s